The super MB
SD C4 dd the
newest function: can support wireless diagnose. 2013.03 Newest version MB SD
Connect C4 with wifi, it support K line,CAN BUS and UDS protocol, fit all
computers,with multi-language. And it supports reading out & erasing
trouble code, reading the real-time data of sensor and actuator, coding and
programming, it also support WIFI.
The
following will teach you how to connect MB STAR compact C4 in a wireless
infrastructure.
1. You can
set your router to have any SSID name. I set mine as workshop, I do recommended
you to use a network key in the following format A123456789365 the number
portion can be any combination. I have tested using various SSID names and any
seem to work fine.
2. Go to
start menu, programs, service, setup Sdnet control and run it, once finished pc
will reboot, I also suggest you delete the configuration from the SD connect.
this is to start fresh.
3. Go to
F:programmeDasbin and open the cal.ini file, you will need to modify from
either T or D2 to W.
4. Be
certain all WIFI and Lan drivers are installed and that you are connected to
the wifi network you will be using. (During this entire process you should
monitor the wifi status as it has a tendency to disconnect at times)
5. we now
need to obtain some basic info from your network, go to start menu, settings,
control panel and open network connections, double click the wireless network
connection once window is open click support tab you will need to write down
the IP address and the default gateway of your system so we can enter them
later in SDNC.
6. Now go to
the SDNC control panel by clicking theMB
SD C4 connect icon
once, after it is open select the configuration tab, click yes in the window
that opens, now go to network, once open start at the bottom, for country
settings leave them set to world, For Road WLAN enter values below: IP address:
192.168.2.222 Subnet mask: 255.255.255.0 Network name: (ssid) Road24h Network
authentication: open (wep128) Select hexadecimal and enter 26 lowercase a.
7. Now for
Workshop WLAN Check the box to Automatically obtain IP address, enter your
network name [SSID] mine is workshop enter Network authentication: WPAPSK
[TKIP] a123456789012
8. Workshop
cable network enter following values: IP address: 169.254.214.163 subnet mask:
255.255.0.0 Once complete click ok.
9. next we
need to manually set the IP address for the SDconnect, this will override the
steps we took in item 8 above, we entered the 169 IP only so it would allow us
to save the other changes we made within SDNC, if the IP was wrong we could not
save any changes. Open control panel then network connections. double click
local area connection, in the window labeled “this connection uses the
following items: look for Internet Protocol (TCP/IP) usually at bottom and
double click it select Obtain an IP address automatically and click ok. now go
back and click Internet Protocol (TCP/IP) again now select Use the following IP
address and enter 172.29.127.112 hit the tab key to auto fill in the subnet
mask and click ok then ok once again on the open window, when complete that
window will automatically close may take a few moments for the IP to save and
register. also make sure the wifi connection is still connected to your
network, it may disconnect after we enter values in SDNC
10. Now we need to power up the
SDconnect of MB
SD C4 using a 12v source. and connect to the pc via LAN cable, once it is
powered up you will need to register/configure SDconnect. do this by going to
the taskbar and click on the SDconnect icon once to open it. Once open click on
Configuration tab then click yes on the pop-up window, next go to the MUX tab
then click Register/configure this will open the SDconnect tool kit. Once open
you can modify the settings that will allow wireless communication. first
choose a number for your SDconnect, I use 9, next region select WORLD, place a
check mark in the square next to WLANprameters,workshop, also place a check
mark in the box to right of the DHCP line, enter the laptop you are using IP
address, in my case it was 192.168.0.9 then enter router IP under Gateway which
in my case was 192.168.0.1. for SSID [router name] enter name of your wifi
network, as stated earlier mine is workshop, for my encryption I used WPA2 /
ASCII my key is A123456789365, after all is entered click the start tab, a
window showing saved configuration will display click ok then close on
SDconnect tool kit window. 11. You can test connection by unplugging the LAN
cable from PC or SDconnect then click the number next to the pad lock icon,
when window opens click the test signal tab you should hear an audible beep
from SDconnect unit. in some situations the box next to the SDconnect icon will
be grey with a red X you must click the grey box and select your MB SD Connect
Compact 4, connect from the list.
